![]() Yes, I think pressing a button is not as bad. I don’t want my fiance to have to speak to Alexa, while she’s trying to get some sleep. Is there a way for it to just interact with the receiver and lower the volume regardless of the activity that’s active? Thank you.Įdit: I should clarify that I am not interested in the Alexa integration of this process at all. If I am watching TV and make the “Volume Down” activity for the Xbox, it will presumably turn off my cable box and switch me over to “Play Xbox”, then lower the volume. The other problem is I am usually watching cable TV or on my Xbox, which involve different devices and are different activities. I don’t really want to leave my TV, receiver, etc on all the time. First of all, it seems like it requires that I change the power settings for all my devices to never turn off, otherwise once the “Volume Down” activity ends, it will turn off the devices. I see the solution here is to create a Harmony activity but this is really confusing to me. I already have a remote for her to trigger certain ST actions, so having a tactile way to lower the volume (one press = 3 click drop) would be great. I am always up hours past her bedtime and sometimes I can’t tell that the volume is too loud. The use case is my fiance goes to sleep early and our bedroom shares a wall with the living room. Hi, I want to have a way that a SmartThings enabled remote can press a button and have it speak to Harmony, to lower the volume on my receiver. There is a max of 20 units for volume change at one time. So “Alexa, tell Harmony volume up by 6” not " Alexa, tell Harmony set volume up by 6" or you won’t get the result you expect. Just be careful not to use the word “set” in your instruction or harmony thinks you want to change your default skip amount. Very nice new feature that was just released this month. And “Alexa, tell Harmony volume down by 10” and both work just as expected. For example, I just tested on mine, and I can say “Alexa, tell Harmony volume up by 8”. Now, however, as long as you have installed the new Harmony red Skill (as opposed to the older harmony blue skill), for many devices you don’t need to use an activity at all. I used “lion” and “tiger” for my two volume up activities, because they were easy to remember and didn’t conflict with any of echo’s reserved words. You may also find that echo doesn’t like switches/activities named with the words that it might use for itself, such as “louder.” Then you could switch back-and-forth between them. That’s why before the official echo/harmony integration, most of us Who require this functionality had two activities for volume up and two activities for volume down. So you wouldn’t be able to do louder, louder, louder in that way. Harmony doesn’t let you repeat the same activity multiple times. Say it again 2 more times and it should go to 15. If you command “louder”, the hub will increase the Then create an activity named “softer” the same way but with only 3 Then customize it withĥ separate commands, spaced 2 seconds apart, that activates your volumeīutton. Is create an activity named “louder” in harmony hub. ![]() To use Harmony as the IF at IFTTT, you have to have Harmony turn on a virtual switch in smartthings, and then that virtual switch coming on becomes the iF.Īnyway, there are a lot of people using bond in the community and lots of people using Harmony, so I’m going to change your topic title to something that should attract their attention and hopefully they will have advice for you.I am no sure what your TV is set to when it first turns on. And it may be able to send some other messages to other devices. Instead, the button sends a “button pressed” message to the network when it is physically actuated. Smartthings can’t send a command to Its own brand button, for example. ![]() That’s true for almost all home automation systems. You can’t send a button an instruction to press itself. The reason nothing else shows up is because nothing else is actionable.īuttons typically do not receive any commands from the network other than a query about the battery level. no buttons, contact sensors, keypads, motion sensors etc. out of the all my devices on smartthings only switches and plugs show up as selectable options. I have paired my SmartThings with my harmony hub but my Smart bulbs (Globe Suite) and Smart switch (TP Link) do not work in the Harmony app. Hello everyone, So I’m new to SmartThings and was hoping for some help. Which can only be connected to home control devices. Db1323 (Daniel ) October 22, 2020, 6:14am 1. Tap Select Harmony Activities and check the activities you want to. Tap Select Harmony Hubs and check the hubs you want to integrate. Discovery should start and after a while ST should find your Harmony Hub(s) and Activities. Tap Connect Now and follow the steps for authentication. I should have mentioned that the Harmony remote has Tap Smartthings Labs Logitech Harmony Home Hub (Labs).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |